Documentation

This page has been automatically translated from Polish with the help of DeepL.
We appreciate your understanding if any translation errors occur.

4.10. Subpanel SIDE GUIDE MARKERS

1. Licensing options and technical support – expand

1. Commercial version – licensing method
2. Technical support

2. About the Impozycjoner B program – expand

      1. Variant B of the Impozycjoner program
      2. Getting started with the program
      3. Program interface

3. Detailed overview of tool panels – expand

      1. F1 IMPOSITION FILES panel
      2. F2 IMPOSITION PARAMETERS panel
      3. F3 SEQUENCE OF SIGNATURES/SHEETS panel
               1. Exception table
               2. Example entries in the exception table
               3. Additional function of the Exception Table
               4. Reverse numbering of signatures and sheets
               5. Sequence of sheets in the signature
      4. F4 CREEP REDUCTION panel
      5. F5 SPACING BETWEEN COLUMNS/ROWS panel
      6. F6 OUTPUT FILE panel
      7. F7 GRAPHIC ELEMENTS ON THE IMPOSITION SHEET panel
      8. F8 FINAL OPTIONS panel
      9. Saving the imposition project
      10. Imposition templates

4. F7 GRAPHICAL ELEMENTS ON THE IMPOSITION SHEET panel

      1. Subpanel CUTTING MARKERS
      2. Subpanel FOLD MARK
      3. Subpanel COLLATION MARK
      4. Subpanel CUT-OFF LINES
      5. Subpanel TEXT FRAMES
      6. Subpanel CODES
      7. Subpanel GEOMETRIC FIGURES
      8. Subpanel ELEMENTS IN PDF FORMAT
      9. Subpanel DENSITOMETRIC STRIPS
      10. Subpanel SIDE GUIDE MARKERS
      11. Subpanel REGISTRATION MARKS
      12. Subpanel OFFSET PLATE COLOR MARKINGS (SEPARATION)
      13. Positioning of texts, codes, figures and PDF elements on the imposition sheet
      14. Placing drawn markers on selected sheets and pages

5. Folding scheme management – expand

      1. List of folding schemes
      2. Missing folding schemes
      3. Editing folding schemes

4.10. Subpanel SIDE GUIDE MARKERS

Important! The F7 GRAPHICAL ELEMENTS ON THE IMPOSITION SHEET panel can be enabled or disabled depending on whether the Activate the panel switch is selected or not. If this panel is disabled, none of the graphical elements specified in this panel will be drawn.


The SIDE GUIDE MARKERS subpanel allows you to place up to 10 PDF files on a sheet, which are saved in the MyImpozycjoner\SGM folder (from Side Guide Marker. It is assumed that these files are side marker files. For one of the 10 side mark files, you can specify on which edge of the paper (left, right, or both) it should be drawn. you can also set the height at which it is to be drawn (with a choice of the edge of the paper from which the height will be measured – top or bottom), and you can also enter an additional paper width marking. Please note that for the mark to function properly, half of its width should extend beyond the paper. The MyImpozycjoner\SGM folder must contain at least one file. The file list contains a pop-up menu for managing the folder contents. The markers used in the project are saved in the project or template file. If these elements are missing when the project is opened, the program recreates them automatically.

The SIDE GUIDE MARKERS subpanel allows you to place up to 10 PDF files on a sheet, which are saved in the MyImpozycjoner\SGM folder (from Side Guide Marker. It is assumed that these files are side marker files. For one of the 10 side mark files, you can specify on which edge of the paper (left, right, or both) it should be drawn. you can also set the height at which it is to be drawn (with a choice of the edge of the paper from which the height will be measured – top or bottom), and you can also enter an additional paper width marking. Please note that for the mark to function properly, half of its width should extend beyond the paper.

The MyImpozycjoner\SGM folder must contain at least one file. The file list contains a pop-up menu for managing the folder contents.

The markers used in the project are saved in the project or template file. If these elements are missing when the project is opened, the program recreates them automatically.